|
|
Thread: FS: 74 REPU $8k, Nashville 37212
[' This thread is 2 pages long: (1)
2 '] |
repu510
Hauling
Posts: 141
|
posted April 09, 2008 02:14 PM |
|
FS: 74 REPU $8k, Nashville 37212
I'm probably going to regret this, but I'm putting the REPU up for sale. New job and other stuff coming up, so I dont have room for this anymore... prefer to sell locally to keep in the state, but money talks.
about 2k miles on rebuilt 13B 4-port motor by C&C of Murfreesboro.
Owned for about 1.5 years. Only put about 1k miles since I've had it.
White w/ black interior
no kids, no pets, non-smoker
Fairly new carpet kit, in good shape. No wear marks or holes.
Rides firm, but very controlled.
Steering pretty tight. Very little play or wander.
Since purchase, I've done the following:
Rear end FD LSD upgrade
New rear leaf bushings
New brake lines all around
New front upper ball joints
New front sway bar bushings
New front idler arm
New KYB Gas-A-Adjust shocks all around
New rear brake shoes
New sliding rear window
Factory A/C (not hooked up yet, but working on it)
New Carter fuel pump
Relined fuel tank (professionally done, not a backyard job)
New fuel hoses
Upgraded to FC alternator w/ internal regulator
Recovered door and kick panels w/ new vapor barrier.
Has Volk TE37X rims, but will remove for lower price.
Can include a few other things if price is right:
Axxis Front brake pads
Outer tie rod ends
Lower ball joints
Mazdaspeed steering wheel (no hub though)
Racing Beat Power Pulse air filter assembly w/ K&N filter
Racing Beat dual belt alternator pulley
New clutch master and slave cylinder w/ SS line
New tail lamp lenses
Extra window crank handle
Extra door release handle
PM me. I'll try to post pics asap.
|
|
anders
Newbie
Posts: 5
|
posted April 09, 2008 05:31 PM |
|
Anders in Alabama
Is this the one I have been waiting for. Please give me your contact info. I don't want to let one this one go. I am 2 hours away and will travel.
Questions
Type of carbeurator system and exaust
Miles on truck
Body condition
Can't wait to hear back.
|
|
repufever
Revvin Up
Posts: 68
|
|
posted April 11, 2008 12:32 AM |
|
74 mazda truck,
Should have the stock carb, a header with flowmaster muffler, and body should still be in great shape.
current owner has put alot into this since he bought this from me.
____________
74 repu (sold Jeff), 76 Repu (Sold B.Waits), 77 Repu, 79 SA, 93 FD, 69 Camaro (wish 3 rotor).
Yes, I have a rotary problem!
IN TN?
|
|
anders
Newbie
Posts: 5
|
posted April 11, 2008 04:11 PM |
|
Nashville Repu
Thanks repu fever for sending additiional info. I was wondering about the engine rebuild. What kind of work did you do to the engine. Was this the original motor. The body and paint look very nice. Did you also do the paint job.
|
|
repuzentn
Redlining
Posts: 225
|
|
posted April 12, 2008 03:58 PM |
|
Wheels
How much do you want to sell your Volk TE37's for?
____________
-'74 Phoenix Blue
-Daily driver ;-)
-Stock GSL-SE engine
-Stock Nikki carb.
-4-spd tranny (time for a
TII one, synchro's are
grinding)
-Racing Beat road-race
headers
-RB 20" pre-silencer
-REV25 Rotor muffler
-Gilmer drive pulleys(fun
while it lasted!)
|
|
repu510
Hauling
Posts: 141
|
|
posted April 13, 2008 12:32 AM |
 Edited By: repu510 on 13 Apr 2008 00:33 |
|
i'd like to sell them with the repu. if it doesn't work out with some of the other members interested in the truck, i'll be posting them here later. thanks for inquiring.
|
|
repuzentn
Redlining
Posts: 225
|
|
posted April 13, 2008 01:18 PM |
|
Alright, thanks for the reply.
____________
-'74 Phoenix Blue
-Daily driver ;-)
-Stock GSL-SE engine
-Stock Nikki carb.
-4-spd tranny (time for a
TII one, synchro's are
grinding)
-Racing Beat road-race
headers
-RB 20" pre-silencer
-REV25 Rotor muffler
-Gilmer drive pulleys(fun
while it lasted!)
|
|
remydrm
Revvin Up
Posts: 92
|
|
posted April 14, 2008 02:35 PM |
|
Do you have any pictures available?
|
|
repu510
Hauling
Posts: 141
|
|
posted April 19, 2008 10:33 AM |
|
if you havent checked the pics out on rx7club or rotarycarclub, pm me and I'll send you some pics.
wanted to add a few more things i forgot to mention:
5 speed manual trans from 79-80 RX7, so shifter lines up nice.
goes into all gears smoothly w/o grinding. also put royal purple gear lube in recently.
vintage wood shift knob w/ rotor and mazda m on top.
mazdaspeed floor mats. (kinda cheap, but better than nothing)
keep the inquiries coming!
|
|
mwpayne
Hauling
Posts: 195
|
|
posted April 19, 2008 05:06 PM |
|
If you don't mind me asking..what shifter do you have in that 5 speed tranny that you put in?
I've just put in an SA in my 74 myself and trying to decide what would be the best way to go.
Thanks, and good luck with the sale!
|
|
repu510
Hauling
Posts: 141
|
|
posted April 21, 2008 07:16 AM |
|
if you are refering to the shift lever itself, it should be a stock 79-80 trans. as far as the knob goes, not sure where it came from. i just happened upon it on ebay. i'll pm you a pic of the shift knob later today if you like.
p.s. it stays w/ the repu. i have no intent of selling it separately, so please don't ask. i know how we all want those few little details that set our vehicle apart from everyone else.
|
|
mwpayne
Hauling
Posts: 195
|
|
posted April 21, 2008 05:39 PM |
Edited By: mwpayne on 21 Apr 2008 17:40
|
|
Hey, no worries, the LAST thing I'd do is ask for parts out of your super nice truck, never crossed my mind. Do you remember if the new lever is the same length as the old truck shifter?
|
|
repu510
Hauling
Posts: 141
|
|
posted April 22, 2008 12:09 AM |
|
dont know where the shift lever came from. it was on the truck when i bought it. it looks taller than the normal rx-7 length, so i'm guessing it is the orig 4spd trans lever or it is from one of the other old school rx's like a 2,3, or 4.
if i remember correctly, the shift levers for all pre-gslse trannies are interchangeable. i even think they're interchangeable w/ 3rd gen trannies too. only trannies from 2nd gen FC Rx-7s are different. Dont quote me, this is just what I vaguely recall hearing, but I could be wrong. I think there are a bunch of combinations that can be swapped around w/ the gear boxes and bell housings to get the right length of tranny for your application. For close gear ratios, I heard the Miata gearbox is the hot ticket for autocrossers which is also interchangeable w/ the rotary trannies.
if Chad or Charles can chime in, they may remember what application the shift lever on the truck came from.
|
|
repu510
Hauling
Posts: 141
|
|
posted May 29, 2008 09:49 AM |
|
|
since there hasn't been much interest, i guess i'll keep it! a few more improvements will probably find their way onto the truck in the meantime...
|
|
tobanybe
Revvin Up
Posts: 80
|
posted September 15, 2008 02:27 AM |
|
tn repu
pm sent hope this is still available, please contact me!!!
:(:)
____________
revin secret 7*
|
|
repu510
Hauling
Posts: 141
|
|
posted September 15, 2008 11:39 AM |
|
|
got your email and replied. on saturday i think?
|
|
tobanybe
Revvin Up
Posts: 80
|
posted September 16, 2008 06:43 AM |
|
~
oh ... For some reason I am not getting any pm's ...bummer ... But u could let Me know here I guess
____________
revin secret 7*
|
|
repu510
Hauling
Posts: 141
|
|
posted September 16, 2008 12:52 PM |
|
|
i'll pm you again w/ my phone#.
|
|
repu510
Hauling
Posts: 141
|
|
posted September 17, 2008 03:21 PM |
|
|
pm'd again. if you dont get it, reply here with a good email address.
|
|
tobanybe
Revvin Up
Posts: 80
|
|
posted September 18, 2008 08:13 AM |
|
~
yeah it's on my end... I am mobile with my Internet so I am sure ....
Tobanybe@hushmail.com
This will work though :)
____________
revin secret 7*
|
|
| All times are PST (US)
[' This thread is 2 pages long: (1)
2 '] |
|
|
