|
|
Thread: * * * lsd kit available * * *
[' This thread is 4 pages long:
1
2 (3)
4 '] |
Brad
Rotorhead
Posts: 1672
|
posted September 24, 2014 03:01 PM |
|
|
Max, when does the 3 rotor peripheral port with sequential no-lift box go in?
|
|
kansei
Redlining
Wankelized
Posts: 423
|
|
posted September 24, 2014 03:01 PM |
|
Ummm.... OK
Dibs.
You never said anything about payment amount or time, so I'll take the deferred payment plan, please. ; )
Neal.
|
|
bosozoku
1st Gear
Posts: 44
|
|
posted September 24, 2014 03:52 PM |
|
REPUMAX
i'll your rear end located in Torrance, ca
|
|
bosozoku
1st Gear
Posts: 44
|
|
posted September 24, 2014 03:54 PM |
|
repumax
i'll buy your rearend. I'm located in Torrance, ca
|
|
Repumax
Redlining
Posts: 427
|
|
posted September 25, 2014 04:00 PM |
|
|
I didn't mean to hi-jack this thread so I'll end it here. I'll be posting it up in the for sale section soon . Neil, you have first dibs and bosozoku second.
|
|
bosozoku
1st Gear
Posts: 44
|
|
posted October 07, 2014 03:21 PM |
|
|
I believe the ring gear spacer is .250 inch thickness? what about the carrier spacer and axle spacer?
|
|
chuyler1
Hauling
Posts: 140
|
|
posted March 27, 2015 07:52 AM |
|
|
I know this is probably beating a dead horse, but I'd like to add this to my truck. If the kit isn't available, can someone share the plans?
|
|
bosozoku
1st Gear
Posts: 44
|
|
posted March 27, 2015 10:29 AM |
|
|
The gear spacer is .25. No one has share the axle spacer specs yet.
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted March 27, 2015 11:21 AM |
|
quote:
The gear spacer is .25. No one has share the axle spacer specs yet.
In Theory the little axle spacer should be as thick as the stock thrust block in the repu open diff. I don't see why it would need to be any different thickness. Just make it out of a hardened steel, since it gets hammered. O.D. should be a loose fit, so it can slide back and forth, but no slop. And allow for some thermal expansion. A guess is 2 thou smaller than axle end O.D.
To answer the other question, I have heard no plans for anyone to reproduce this kit.
Subject of the thread should be changed to *NOT* available.
You likely could take this info to a reputable gear shop with your REPU pumpkin, and 3rd gen Torsen, and ask them to get er done.
|
|
bosozoku
1st Gear
Posts: 44
|
|
posted April 04, 2015 02:31 PM |
|
|
what material was the .25" ring gear spacer made of? steel or aluminum?
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted April 05, 2015 11:26 PM |
|
Steel, you don't want any aluminum in there. But an aluminum carrier would be SWEET.
____________
-brad-
74 REPU Lawn Green
81 Rx-7 racecar. 12a J-
Bridge
|
|
| All times are PST (US)
[' This thread is 4 pages long:
1
2 (3)
4 '] |
|
|
